- 您现在的位置：买卖IC网 > Sheet目录353 > R1EX25064ASA00A#S0 (Renesas Electronics America)IC EEPROM 64K 5MHZ 8SOP
R1EX25032Axx00A/R1EX25064Axx00A
Hold Condition
The hold ( HOLD ) signal is used to pause any serial communications with the device without resetting the clocking
sequence.
During the hold condition, the serial data output (Q) is high impedance, and serial data input (D) and serial clock (C)
are don’t care.
To enter the hold condition, the device must be selected, with chip select ( S ) low.
Normally, the device is kept selected, for the whole duration of the hold condition. Deselecting the device while it is in
the hold condition, has the effect of resetting the state of the device, and this mechanism can be used if it is required to
reset any processes that had been in progress.
The hold condition starts when the hold ( HOLD ) signal is driven low at the same time as serial clock (C) already being
low (as shown in the following figure).
The hold condition ends when the hold ( HOLD ) signal is driven high at the same time as serial clock (C) already being
low.
The following figure also shows what happens if the rising and falling edges are not timed to coincide with serial clock
(C) being low.
Hold Condition Activation
HOLD status
HOLD status
C
HOLD
Notes
Data Protection at V CC On/Off
When V CC is turned on or off, noise on S inputs generated by external circuits (CPU, etc) may act as a trigger and turn
the EEPROM to unintentional program mode. To prevent this unintentional programming, this EEPROM have a power
on reset function. Be careful of the notices described below in order for the power on reset function to operate
correctly.
? S should be fixed to V CC during V CC on/off. Low to high or high to low transition during V CC on/off may
cause the trigger for the unintentional programming.
? V CC should be turned on/off after the EEPROM is placed in a standby state.
? V CC should be turned on from the ground level (V SS ) in order for the EEPROM not to enter the unintentional
programming mode.
? V CC turn on speed should be slower than 10 μ s/V.
? When WRSR or WRITE instruction is executed before V CC turns off, V CC should be turned off after waiting
write cycle time (t W ).
REJ03C0358-0002.Rev.0.02 Jan.14.2009
page 18 of 20
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
R1EX25512ATA00A#S0
IC EEPROM 512K 5MHZ 8TSSOP
RA1P011FP1
CONN PLUG 11POS STRAIGHT GOLD
RACD03-700
LED DRIVER 3W 10-43V OUT SGL
RACD06-700
LED DRIVER 6W 3-8.5V OUT LED DR
RACD12-500
LED DRIVER 0.5AOUT 3-24VDC OUT
RACD20-350D
LED DRIVER 230VAC 2X(3-34)V OUT
RACD20-700
LED DRIVER 0.7AOUT 100-240VAC
RACD30-500
LED DRIVER 30W 10-56V OUT SGL
相关代理商/技术参数
R1EX25064ASA00G
制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface 32k EEPROM 64k EEPROM
R1EX25064ASA00I
制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface Electrically Erasable and Programmable Read Only Memory
R1EX25064ASA00I#S0
制造商:Renesas Electronics Corporation 功能描述:SERIAL EEPROM 64K, SPI, SOP8, 制造商:Renesas Electronics Corporation 功能描述:SERIAL EEPROM 64K, SPI, SOP8, I-GRADE - Tape and Reel 制造商:Renesas Electronics Corporation 功能描述:IC EEPROM 64KBIT 5MHZ 8SOP
R1EX25064ATA00A
制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface Electrically Erasable and Programmable Read Only Memory
R1EX25064ATA00A#S0
功能描述:IC EEPROM 64K 5MHZ 8TSSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:1 系列:- 格式 - 存储器:闪存 存储器类型:闪存 - NAND 存储容量:4G（256M x 16） 速度:- 接口:并联 电源电压:2.7 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP I 包装:Digi-Reel® 其它名称:557-1461-6
R1EX25064ATA00G
制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface 32k EEPROM 64k EEPROM
R1EX25064ATA00I
制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Serial Peripheral Interface Electrically Erasable and Programmable Read Only Memory
R1EX25064ATA00I#S0
制造商:Renesas Electronics Corporation 功能描述:SERIAL EEPROM 64K SPI, TSSOP8, 制造商:Renesas Electronics Corporation 功能描述:SERIAL EEPROM 64K SPI, TSSOP8, I-GRADE - Tape and Reel 制造商:Renesas Electronics Corporation 功能描述:IC EEPROM 64KBIT 5MHZ 8TSSOP